CG 150cc Piston Assy Pin 13mm

CG150 Piston Assembly · 13mm Piston Pin

🔧 Piston Assembly · 13mm Piston Pin · Engine Rebuild Part · CG Series Parts

For CG150 · CG125 (13mm Pin Version) · Honda Style 4-Stroke Engines

This is the CG150 Piston Assembly (13mm Piston Pin), a high-quality, cost-effective replacement for CG series engine rebuilds or performance restoration. Specifically designed for CG150 and some CG125 (13mm piston pin version) 4-stroke engines.

This piston assembly includes piston, piston rings (compression rings + oil ring), piston pin, and circlips, providing all the essential components needed for a complete piston system overhaul. The piston is manufactured from high-quality aluminum alloy with precision machining to ensure optimal fit with the cylinder wall, restoring engine power and compression performance.

⚠️ Important: Piston Pin Size Confirmation

This product is the 13mm piston pin version. CG series engines come in two piston pin sizes: 13mm and 15mm. Please verify your original engine's piston pin diameter before purchasing.
CG150 engines typically use 15mm piston pins. CG125 engines are available in both 13mm and 15mm versions. Carefully check your original piston pin size to avoid ordering the wrong part.

Compatible Engine Models: CG150 (13mm piston pin version) · CG125 (13mm piston pin version) and Honda-style 4-stroke engines

Compatible Vehicles:

• CG150 Motorcycles (13mm piston pin version)
• CG125 Motorcycles (13mm piston pin version)
• Honda CG Series Models
• Other motorcycles and ATVs equipped with Honda-style CG series engines

• High-Quality Aluminum Alloy Piston: Cast from high-strength aluminum alloy for lightweight construction, high strength, low thermal expansion, and excellent wear resistance.
• Precision Machining: Precision-machined piston skirt ensures accurate cylinder wall clearance for smooth operation.
• Complete Piston Ring Set: Includes 2 compression rings and 1 oil ring for optimal sealing and oil control.
• 13mm Piston Pin: Features 13mm diameter piston pin, suitable for 13mm pin version CG125/CG150 engines.
• OEM Specification: Manufactured to exact CG series engine factory specifications for a perfect replacement of worn components.
• Cost-Effective: Excellent value, ideal replacement for original factory piston assemblies.

🔧 Installation Guide

1. Remove the cylinder head and cylinder block, then remove the piston and connecting rod assembly.
2. Remove the old piston pin circlips, push out the piston pin, and separate the piston from the connecting rod.
3. Thoroughly clean the piston ring grooves and connecting rod small end, removing all carbon deposits and contaminants.
4. Inspect the connecting rod small end bushing for wear; replace if necessary.
5. Install the new piston rings into the ring grooves, paying attention to orientation (marked side typically faces up).
6. Stagger ring gaps 120 degrees apart to prevent gas leakage through overlapping gaps.
7. Insert the piston pin through the piston and connecting rod small end, then install new circlips, ensuring they are fully seated in the grooves.
8. Before installation, apply a small amount of engine oil to the piston rings and cylinder wall for lubrication.
9. Use a ring compressor to install the piston into the cylinder, ensuring correct connecting rod orientation.
Important Note: Circlips must be fully seated in the grooves — failure to do so may cause the piston pin to dislodge, resulting in severe engine damage. Professional installation is strongly recommended.

Proper break-in after installing a new piston assembly is essential for optimal ring-to-cylinder wall seating:

• Break-In Period: Recommended 500-1000 km (300-600 miles).
• RPM Control: Avoid prolonged high RPM operation during break-in; keep RPM below 70% of maximum.
• Load Control: Avoid hard acceleration, heavy loads, and steep hill climbing during break-in.
• Oil Change: Change oil after the first 300 km (180 miles), and again after the break-in period is complete.
• Oil Quality: Use high-quality mineral oil during break-in; switch to synthetic oil after break-in.

⚠️ Important Notice: This is the CG150 Piston Assembly (13mm piston pin), designed for CG150 and CG125 (13mm piston pin version) engines.
Spec Confirmation: Please verify your original piston pin diameter before purchasing. CG series engines come in both 13mm and 15mm piston pin sizes. This product is the 13mm piston pin version and is NOT compatible with 15mm pin engines.
Installation Note: Piston assembly installation involves critical engine components. Professional installation is strongly recommended. Ensure circlips are fully seated in the grooves for safety.
Recommended Parts: When replacing the piston assembly, inspect cylinder wear and consider replacing the cylinder block or re-boring if necessary. Product images are for reference only; actual product may vary.